Abbey Systems
  • Home
  • About
    • History
    • Our People
  • Latest News
  • Products
    • Aspex SCADA HMI software
    • Powerlink Telemetry Server SCADA software
    • Remote Access >
      • WebAlarm - Browser based access for smartphones
      • Securelink - Encrypted remote laptop PC access
    • SCADA Gateways - IP to Radio communications interfaces
    • Powercat RTU - Substation Monitoring & Control
    • Topcat RTU - Feeder Line Automation
    • Swampfox RTU - Pump Station & Reservoir Controller
    • Fox - Fibre Optic Converters
    • Accessories
  • Papers
    • Resilience in Water & Wastewater Telemetry & Control Systems 2015
    • Telemetry Communications Present & Future 2010
    • Telemetry Communications of the Future 2003
    • Evolution of SCADA Systems 2003
    • Telemetry / SCADA Open vs Proprietary Systems 2003
    • Getting more from your sewage pumping network 2000
  • SCADA Applications
    • Load Management System
    • HVDC Power - Fast Reaction Emergency Dump System
    • Pump Station Controller Program suite
    • Frequently Asked Questions
  • Case Studies
    • Gas SCADA Systems >
      • Powerco Gas Reticulation Cellular SCADA System
      • Synfuels - Gas pipeline monitoring & leak detection
      • Caltex Oil EMS
      • Petralgas Pipeline SCADA
    • Water & Wastewater SCADA Systems >
      • Neahkahnie, OR, USA
      • Rotorua DC, New Zealand
      • SCADA Experience - water & wastewater systems
    • Power & Energy SCADA Systems >
      • Bangladesh, Chittagong 33/11kV SCADA System
      • Devonport Naval Base Energy Management & Billing
      • SCADA Experience - Power & Gas systems
  • Links
  • Contact

Pump Station Controller Program suite

Picture
A Swampfox RTU based Automatic Pump Control program suite with; support for 1-4 pumps in either duty-assist or duty-standby configurations; automatic duty-pump change-over; remote pump control and set point setting; derived inflow and outflow rate calculations; data logging configured.
  • Maximise the use and processing power of your Swampfox RTU
  • Save the cost of installing a separate Pump Controller
  • Save the cost of a flow meter installation by calculating the inflow from the well rise rate.
  • Minimise the cost of the well level transducer required

Features:
  • Controls 1 to 4 pumps
  • Individual start & stop levels for each pump
  • Setpoints are time stamped and stored in persistent memory at the Master and RTU
  • Adjustable for Duty/Standby or Duty/Assist operation with automatic change over in a fault scenario
  • Automatic delay between pump starts
  • Automatic duty changeover after each pump cycle
  • Pump run-on alarm
  • Individual pump over-current and under-current (cavitation) alarms and dedicated I/O to record current when fault occurred
  • Individual pump run hours and number of starts
  • Derived Inflow and Outflow rates based on well dimensions and level changes
  • Level alarms for High/Low/Failed
  • Watchdog output pulses every minute if program and setpoints are loaded
  • Designed for a Swampfox 3, available in a Swampfox 1 for 1-2 pump sites
  • Fully set up for data logging
  • Highly customisable
  • Pumps can be remotely run or taken out of service
  • Provisioned for dedicated flow meter if available
  • Full program documentation provided - you own the programs and they reside in your SCADA Master
  • Optional onsite Touchscreen HMI

Site Input / Outputs:

To provide for the automatic program pump control, the following live site RTU inputs / outputs are required:

Individual pump status inputs;
  • Pump Running
  • Pump in Auto or Off / Manual control
  • Pump Faulty (i.e. TOL status input, etc.)
  • Well level and pump currents (optional) analogue values
Controls (Outputs)
  • Individual pump run outputs

Picture
Picture
Picture
Supervisory Control and Data Acquisition Product Designers & Manufacturers